SmallHD Camera Control lets you adjust supported camera settings from your monitor, including exposure, recording, and camera menus. Each Camera Control license is registered to one monitor. This article covers how to purchase a license, activate it, install it on your monitor, and connect your camera. Setup details for each camera are in that camera's connection guide.
Purchase a Camera Control License
- Go to the SmallHD Camera Control page.
- Select your camera manufacturer and model.
- Choose the Camera Control license or kit for your SmallHD monitor, then complete your purchase. If you purchase a digital license, you will receive an activation code by email. License kits include an activation card.
NOTE: Some cameras need additional cables or adapters. Check the product page for hardware requirements before you purchase.
Activating a Camera Control license permanently registers it to one SmallHD monitor. You cannot remove or transfer the license to another monitor. Make sure you activate the license on the monitor you intend to use with your camera.
Activate the License
Activation registers the license to your monitor on the SmallHD activation site. You need the monitor's Monitor Token and serial number. The site then provides a license file for PageOS 6.4.2 and later, or a license key for PageOS 6.4.1 and earlier.
1. On your monitor, navigate to Monitor Settings > System > Licenses and note the Monitor Token (see image below). For PageOS 6.4.1 and earlier, select Add a License to display the token.
2. On your computer or phone, start the activation process:
- Digital purchase: Open the activation email, then select Begin Activation.
- Activation card: Go to activate.smallhd.com, enter the code from your card, then select Go (see image below).
3. Enter your Monitor Token, then verify it when prompted.
4. Enter your monitor's serial number.
5. Enter your name and email address. To send the license to additional email addresses, enter them here.
6. Complete the activation process. The site displays your license file or license key (see image below) and emails you a copy. Follow the installation steps below for your PageOS version.
Install the License File (PageOS 6.4.2 and Later)
On PageOS 6.4.2 and later, you can load the license onto the monitor as a file from an SD card or flash drive. The monitor installs every valid license file it finds in the top-level folder of the inserted cards and drives, so you can install several licenses at once.
- Download the license file from the activation site or from your activation email. The filename uses the format <token>_<license item>.shdlicense.
- Copy the license file to the root directory of an SD card or flash drive. Do not place the file in a subfolder.
- Eject the card or drive from your computer, then insert it into your monitor.
- On your monitor, navigate to Monitor Settings > System > Licenses, then select Install next to Install from removable media. The monitor scans the card or drive, displays Licenses Installed Successfully, and lists the installed licenses (see image below).
5. Select OK. Verify that your licenses appear under Installed Licenses.
NOTE: OLED 16 does not have an SD card slot. Use a flash drive to install the license file.
Install the License Key (PageOS 6.4.1 and Earlier)
On PageOS 6.4.1 and earlier, you enter the license key on the monitor.
1. On your monitor, navigate to Monitor Settings > System > Licenses > Add a License.
2. Enter the license key from the activation site or email, then select Activate. The monitor returns to the Licenses page and displays the installed license (see image below).
Connect Your Camera
Connection requirements vary by camera manufacturer and model. For cables, camera settings, and supported features, see the connection guide for your camera: camera connection guides.
- Verify that your monitor runs a PageOS version that supports your camera. Download PageOS firmware from downloads.smallhd.com.
- Connect your camera to the monitor using Ethernet, USB, or a supported wireless connection, as specified in your cameras connection guide.
- On your monitor, navigate to Monitor Settings > Accessories > Camera Control, then select your camera.
- Follow the on-screen instructions to complete the connection. Once connected, the camera controls appear in the border around the image.
Troubleshooting
No activation email or card.
Check the email account you used for the purchase, including the spam or junk folder. If you bought a physical kit, check the activation card in the kit.
No Removable Media Detected
The monitor did not find an SD card or flash drive. Select OK, insert the card or drive, then select Install again.
Valid License File Not Detected
The monitor did not find a valid license file in the top-level folder (see image below). Select Select File to choose the file in the File Browser, or Not Now to cancel. Check that the file is in the top-level folder, not in a subfolder.
License Already Installed
The monitor already has this license installed. Select OK to dismiss the message.
Invalid License File
The license file may be damaged or registered to another monitor. Download the file again from your activation email, then repeat the installation process. If the error persists, contact SmallHD Support.
License key not accepted (PageOS 6.4.1 and earlier)
Verify that you entered the license key correctly. If the monitor indicates that the license is already active, you do not need to install it again.
Moving a license to another monitor
You cannot remove or transfer a Camera Control license to another monitor after activation.





